Riccardo Riva

Posts Tagged ‘teaming’

This simple post will show how to configure Ethernet Bonding on two (or more) network interfaces on RHEL 5 or CentOS 5.
I’ve tested this configuration on a CentOS 5.2 with kernel 2.6.18-92.1.22.el5 as you could see below :

uname -a

Linux serverlab.riccardoriva.local 2.6.18-92.1.22.el5 #1 SMP Tue Dec 16 11:57:43 EST 2008 x86_64 x86_64 x86_64 GNU/Linux

cat /etc/redhat-release
CentOS release 5.2 (Final)

If you want to create a bonding on two interface (i.e. eth0 and eth1) you should do the following :

Edit /etc/sysconfig/network-scripts/ifcfg-eth0

# Bonding eth0 to bond0
DEVICE=eth0
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0
SLAVE=yes
USERCTL=NO

Edit /etc/sysconfig/network-scripts/ifcfg-eth1

# Bonding eth1 to bond0
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0
SLAVE=yes
USERCTL=NO

Copy /etc/sysconfig/network-scripts/ifcfg-eth1 to /etc/sysconfig/network-scripts/ifcfg-bond0 to keep the same file permission by executing the following commands :

cd /etc/sysconfig/network-scripts
copy ifcfg-eth1 ifcfg-bond0

Edit /etc/sysconfig/network-scripts/ifcfg-bond0

ifcfg-bond0
DEVICE=bond0
BOOTPROTO=none
ONBOOT=yes
NETWORK=10.100.100.0
NETMASK=255.255.255.0
IPADDR=10.100.100.1
USERCTL=NO

Edit /etc/modprobe.conf adding the following line :

alias bond0 bonding

Reboot your system to let modules be loaded or load it manually with the following command :

insmod bond0 bonding

If you haven’t rebooted your system, restart your network with the following command :

/etc/init.d/network restart

You should check if bonding is working you should look at /proc/net/bonding/bond0 with the following command :

cat /proc/net/bonding/bond0

and you should see something similar to the following :

Ethernet Channel Bonding Driver: v3.2.4 (January 28, 2008)

Bonding Mode: load balancing (round-robin)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:15:17:88:5a:3c

Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:15:17:88:5a:3d

You’ve done

Hope this help

Bye
Riccardo

Bookmark It

This post will explain hot-to configure a unique IP Address on multiple NICs (Phisical or Virtual) on Debian GNU/Linux (with a 2.6 kernel).

This post assume you have a 192.168.0.0/24 network and that you want to assign 192.168.0.10/24 to your system.
Read the rest of this entry »

Bookmark It

Ethernet bonding refers to aggregate multiple ethernet channels together to form a single channel. This is primarily used for redundancy in ethernet paths or for load balancing. This page refers to ifenslave mode in particular to configure ethernet bonding on Linux systems, and so doesn’t limit itself to discussion of 802.3ad Trunk Aggregation.
I’ve used the following modes a lot of time under Debian or Ubuntu and on Open-E.

Read the rest of this entry »

Bookmark It

This post will explain hot-to configure a unique IP Address on multiple NICs (Phisical or Virtual) on RedHat Linux (or Fedora).

This post assume you have a 192.168.1.0/24 network and that you want to assign 192.168.1.1/24 to your system.

Read the rest of this entry »

Bookmark It